Reservoirs
Hychem has a range of potable water approved coatings and repair mortars for use in reservoirs.
Sub-Categories
Repair, rehabilitate, coat and protect to stop corrosion. Increase asset life span with our range of specialist products below:
Products
- TL6 – Water potable epoxy coating. Add 500ml epoxy pigment – Hychem TL6 is a specialised water potable coating suited to a large range of applications. TL6 can be roller applied to vertical and horizontal substrates including concrete and steel. TL6 is a high-build, multipurpose, solventless epoxy coating exhibiting a chemically resistant high gloss stippled finish. Hychem TL6 is suited to water potable environments. It conforms to to AS/NZS 4020/2005 testing of products for use in contact with drinking water.
- TL5 EPL – HYCHEM TL5 EPL is a chemically resistant high-build epoxy coating designed for use in environments where exposure to water, salt solutions, alkali and dilute mineral acids is required. The product is designed for applications of up to 6mm+ using wet on wet spray technique, but can also be trowelled in small areas where spray application is unsuitable. HYCHEM TL5 EPL is based on the same resin as HYCHEM TL5 but uses a slower hardener system to allow a longer work time. This change in hardener results in equally good sulphuric acid resistance compared to TL5.
- WP120
- CW111 – VELOSIT CW 111 is a High Strength Crystalline Waterproofing slurry for concrete substrates. It is very economic and easy to apply. VELOSIT CW 111 becomes part of the concrete and creates a waterproof layer inside the concrete itself. It is especially strong against negative side water pressure. Self healing properties of up to 0.4 mm static cracks Unsurpassed strength development with more than 20 MPa after 24 h and more than 50 MPa after 28 days
- RM205 – VELOSIT RM205 Structural Concrete Repair Mortar 6 – 100 MM – 45MPa a cementitious repair mortar for concrete restoration acc. to EN 1504-9. It is used to fill large voids or build up larger cross-sections up to 100 mm. Potable Water Approved – AS/NZS 4020:2005
Repair, rehabilitate, coat and protect to stop corrosion. Increase asset life span with our range of specialist products below:
Products
- TL6 – Water potable epoxy coating. Add 500ml epoxy pigment – Hychem TL6 is a specialised water potable coating suited to a large range of applications. TL6 can be roller applied to vertical and horizontal substrates including concrete and steel. TL6 is a high-build, multipurpose, solventless epoxy coating exhibiting a chemically resistant high gloss stippled finish. Hychem TL6 is suited to water potable environments. It conforms to to AS/NZS 4020/2005 testing of products for use in contact with drinking water.
- TL5 EPL – HYCHEM TL5 EPL is a chemically resistant high-build epoxy coating designed for use in environments where exposure to water, salt solutions, alkali and dilute mineral acids is required. The product is designed for applications of up to 6mm+ using wet on wet spray technique, but can also be trowelled in small areas where spray application is unsuitable. HYCHEM TL5 EPL is based on the same resin as HYCHEM TL5 but uses a slower hardener system to allow a longer work time. This change in hardener results in equally good sulphuric acid resistance compared to TL5.
- WP120
- CW111 – VELOSIT CW 111 is a High Strength Crystalline Waterproofing slurry for concrete substrates. It is very economic and easy to apply. VELOSIT CW 111 becomes part of the concrete and creates a waterproof layer inside the concrete itself. It is especially strong against negative side water pressure. Self healing properties of up to 0.4 mm static cracks Unsurpassed strength development with more than 20 MPa after 24 h and more than 50 MPa after 28 days
- RM205 – VELOSIT RM205 Structural Concrete Repair Mortar 6 – 100 MM – 45MPa a cementitious repair mortar for concrete restoration acc. to EN 1504-9. It is used to fill large voids or build up larger cross-sections up to 100 mm. Potable Water Approved – AS/NZS 4020:2005